How to Set up a Bathtub Yourself
How to Set up a Bathtub Yourself
Blog Article
Do you find yourself trying to find advice concerning A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult job. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old bathtub and place the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Rather than hiring a professional to take over a halfway-completed job, it is far better to consider employing one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have already purchased a new tub as well as do not need to alter the setup of your previous water supply pipes.
Your tools and also product checklist ought to consist of the following:
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints as well as new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally examine the overflow outlet as well as the normal outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait up until the bath tub has been utilized at the very least once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical faucet adapters. The previous kind should be connected to the tap ends first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in problems with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a passionate person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that piece of content was a smart idea. Feel free to take the time to distribute this write-up if you enjoyed reading it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Estimate
Report this page